PTO BUILD COMPLETE

A30 Series Power Take Off

Model Number

A30A1007MX3X4BX

Build ID

Use this unique build ID when referencing your order

24800832163491

List Price

CONTACT CUSTOMER SERVICE FOR PRICING

Build Breakdown

Manufacturer: ALLISON

Model: 3000 Series (EVS, RDS, SPS) (MHS, BUS, TRV Optional)


Bolt Type: ALLISON 10-BOLT OPENING

Rotation: CRNK

PTO %: 99%

Torque: 415 lbs.ft.

HP: 79 HP

PTO Series: A30 Series

Transmission Gear: A10

Gear Ratio: 07

Shift Type: MX - Constant Drive

Assembly Arrangement: 3

Output Type: X4 - 1410 COMPANION FLANGE

Special Feature: BX - HOSE KIT FOR TOP OPENING


Select your flange position:

The A20 and A30 features a rotatable flange with 30 unique positions. Select the PTO opening you intend to use below to review the 30 position codes.

Once you have found the ideal flange position, you can add the position code characters to the end of the A20 or A30 part number (shown in red below) to have the flange shipped with the preferred arrangement. Alternatively, you can easily set this arrangement before, during, or after installing the PTO.

Pre-set position may not be available through all distribution partners.

A20 - A10 07 - HX 3 BB PX - XX


A30 - A10 07 - MX 3 BB PX - XX






POWER TAKE OFF
  • A30A1007MX3X4BX
    PTO Part Number
    $0.00
  • TOTAL
    $0.00
FOOTNOTES
MODEL FOOTNOTES
ADAPTER FOOTNOTES
PTO FOOTNOTES
CD05 PTO available and has same output shaft speed as the CD10. 07 ratio through 12 ratio. CD05 is smaller and has "C" (1410) output option only.
13
2008 & later Ford F650 or F750 vehicles have interference to the spring hanger bolts. Some success has been achieved by reversing the direction in which the bolts have been installed.
10
PTO available with Muncie Start®; SX shift code (A20), or "6" special feature code on CS41.
17
The torque rating of this PTO is based on the Allison drive rating (for single PTO) of 485 lb.ft. continuous rating and is shown on this page. The CS41 and CD40 PTO ratings are found on page 22 with continuous ratings for Fire pump applications to be calculated as shown on page 3. Ratings above the transmission rating are not approved. Refer to the Allison Tech Data Book for more information. Based on the PTO rating shown on page 22, the CS41-A1007 is rated to 485 lb.ft. intermittent and 420 lb.ft. continuous when used on this transmission. The CS41-A1010 is 336 lb.ft. continuous and intermittent and the CS41-A1012 is 298 lb.ft intermittent and continuous. (for 2 PTOs the total torque rating is 685 lb.ft. at the transmission gear.)
6
Standard option "C" (1410 companion flange) shown. Light duty application can use the "B" output option which will reduce available PTO output torque to 210 lb. ft.
5
Use A20 Series PTO for right side Hino Chassis. Optional, shift code "HH" (2015 - 2020 MY trucks) or "H2" (2021 & Later) provides Hino wiring connections for integrated PTO control.
11
PTOs CD10 or CD05. CD05 PTO available with "C" output for tight clearance chassis applications. Available in 07 ratio and higher with the same speeds and torque ratings as the CD10.
12
A20 has a single continuous/intermittent duty rating.
15
CS10, CS41, and A20 PTOs in Fire Pump application are approved to 4000 RPM output shaft speed.
16
Interference to the end cover of the CS24 can be minimized by use of the CS25 housing option, which has a remote solenoid.
3
Interference to the end cover of the CS10 can be minimized by use of the CS11 housing option, which has a remote solenoid. On A20 use "HR" shift code.
4
CS10, CS41, and CS24 will not install on Ford Louisville or Sterling prior to 2003 due to Interference with CAT 3126 engine mounting bracket. The CS25 is recommended on chassis 2003 and later.
2
3700 series Allison PTOs left side only. No extended shaft unit available. See application ALLI-11 for details.
14
GM Chassis with RPO # PTO, use harness kit 34TK4504, sold separately.
7
PTO shown with assembly arrangement with output shaft low and to the rear. The shaft high assembly can be used in chassis with interference with the PTO shown. Direct mount pump applications may have clearance depending on the type of pump used. The shaft high assembly of the PTO may also allow direct mount pump installations. Due to the numerous chassis and engine combinations it is not possible to note all the information here.
1
Connection to Allison "PTO Enable" circuit must be made when PTO is engaged. Contact dealer for connection type and location.
8
International shift option code 60ABE for clutch shift PTOs.
9
  • Rotatable pump flange 
  • Increased clearance for easier installation
  • Tapered roller bearings increasing PTO life
  • Increased output shaft diameter for higher durability
  • Reduced leak paths
  • Maximized gear design for noise reduction
  • Single intermittent/continuous torque rating
  • Three housing arrangements
  • Extended length PTO mounting fasteners
  • Compatible with EX Drive shaft extension

 

AVAILABLE WITH THE EX DRIVE SHAFT EXTENSION

The Muncie EX Drive was designed to fit on Allison 3000 and 4000 series transmissions with retarder or cooler, and allows for large gear or piston pumps to be direct mounted, eliminating the need for timely driveline installations. The EX Drive provides maximum torque from the PTO, and is available for the A30 Series PTO.

The Muncie Power Take-Off is warranted to be free of defects in material or workmanship and to meet Muncie’s standard written specifications at the time of sale. Muncie’s obligation and liability under this warranty is expressly limited to repairing or replacing, at Muncie’s option, within one year (two years on Allison World Transmission PTOs) after date of original installation any defective part or parts or any product not meeting the specifications.

 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. MUNCIE MAKES NO WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR PURPOSE. MUNCIE’S OBLIGATION UNDER THIS WARRANTY SHALL NOT INCLUDE ANY TRANSPORTATION CHARGES OR COSTS OF INSTALLATION OR ANY LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR DELAY. THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE, AND MUNCIE’S LIABILITY WITH RESPECT TO ANY CONTRACT OR SALE OR ANYTHING DONE IN CONNECTION THEREWITH, WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, OR OTHERWISE, SHALL NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCT OR PART ON WHICH SUCH LIABILITY IS BASED.

 

If requested by Muncie, products or parts for which a warranty claim is made are to be returned transportation prepaid to a Muncie Service Center. Any installation or use not in accordance with catalog or package instructions, other improper use, operation beyond capacity, substitution of parts not approved by Muncie, use with equipment other than the equipment on which the Power Take-Off is first installed, or alteration or repair made to the Power Take-Off other than at a Muncie Service Center, shall void this warranty. No employee or representative of Muncie is authorized to change this warranty in any way or to grant any other warranty.

Prices in this program do not constitute an offer to sell. Suggested prices may change without notice. Please contact Muncie Power Products or your local distributor for current pricing on any items listed as $0.00. All prices are in U.S. dollars.

All information included in the M-Power Spec program is complete and correct to the best of our knowledge. However, we cannot assume any responsibility for errors.

© 2021 Muncie Power Products, Inc.